Di­rect in­for­ma­tion and high trans­paren­cy – all facts about our prod­ucts at a glance

High pres­sure plunger pumps of the large pump se­ries from URA­CA are de­signed and man­u­fac­tured for a vast va­ri­e­ty of ap­pli­ca­tions with re­spect to pow­er and pumped medi­um, where­by the machines nor­mal­ly work in cont­in­u­ous op­er­a­tion. Max­i­mum drive pow­ers range up to 2,600 kW/3,485 HP. The flow vol­umes may reach up to 11,000 l/min/2,906 US­gpm, the op­er­at­ing pres­sure can be 3,000 bar/43,500 psi and high­er [more...]

Al­most all de­posits in au­to­claves, re­ac­tors, spray tow­ers and other con­tain­ers can be re­moved with high pres­sure wa­ter. A high pres­sure plunger pump press­es wa­ter through the noz­zles of the URA­CA tank clean­ing head TWK with a pres­sure of more than 2,000 bar / 29.000 psi. The wa­ter jet cuts through the de­posits and with its defined se­quence of mo­tion guar­an­tees sur­face cov­er­ing re­mo­val of th­ese dirt de­posits [more...]

In the ex­trac­tion of ac­tive and valu­able sub­s­tances, aro­mat­ic and flavour­ing sub­s­tances, the food and phar­ma­ceu­ti­cal in­dus­try is forced to make high de­mands con­cern­ing qual­i­ty and econ­o­my of the ex­trac­tion pro­cess. The CO2-method is there­fore pre­fer­ab­ly used in the ex­trac­tion of pri­mary veg­etable prod­ucts. The op­ti­mal se­quence of the pro­cess [more...]

The new KD718 is the fur­ther de­vel­op­ment of the KD716 for sew­er clean­ing ap­pli­ca­tions. The new pow­er end with ad­di­tio­n­al pow­er end seal­ing by de­fault char­ac­ter­izes this pump type. This means greater avai­l­a­bil­i­ty and longer op­er­a­tion time for rough day-to-day op­er­a­tion. The pump com­bines the ad­van­tages of the thou­sand fold ap­proved KD716 with the eco­log­i­cal­ly ben­e­fi­cial pow­er end seal­ing with equal fitt­ing di­men­sions [more...]

The high­ly flex­i­ble mul­ti-us­er sys­tem en­abling the ex­pan­sion of ex­ist­ing URA­CA is a Eu­ro­pean lead­er with their broad spec­trum of high-pres­sure pump sys­tems for ef­fec­tive sew­er clean­ing. URA­CA pumps with a ca­pac­i­ty be­tween 30 and 180 kW / 40 and 241 HP cov­er the en­tire re­quire­ment spec­trum for all jobs in sew­er clean­ing. URA­CA al­so sup­plies spray guns, th­ese are main­ly used for flush­ing away any resi­d­u­al dirt de­posits in the sew­er di­rect­ly un­der the man­hole open­ing, or to clean out the re­ceiv­ing rills for the man­hole cov­er [more...]

Wher­ev­er in­dus­trial pipes, pipe as­sem­blies, valves or hous­ings must be ab­so­lute­ly tight the leak in­tegri­ty is test­ed with test pumps. The re­quired test pres­sure can be cre­at­ed with them right on site, de­pend­ing on the mod­el. The drive can be de­signed as man­u­al, elec­tri­cal or petrol-pow­ered drive. Re­spec­tive con­trols and valves there­by per­mit the re­pro­du­ci­ble "trac­ing" of test pres­sure curves and al­so the gen­er­a­tion of test pro­to­cols [more...]

New pumps for pres­sure test­ing

Wher­ev­er in­dus­trial pipes, pipe as­sem­blies, valves or hous­ings must be ab­so­lute­ly leak tight, the in­tegri­ty is checked with test pumps. [more...]

Highh­pres­sure pump sys­tems for e ec­tive sew­er clean­ing

URA­CA Pum­pen­fab­rik, head­quar­tered in Bad Urach in the south of Ger­many, is a lead­ing man­u­fac­tur­er of high pres­sure clean­ing sys­tems and com­po­nents. [more...]